Description
*While this part is a drop in fit in many pistols, gunsmith fitting may be required on some guns. The .200" (nominal) diameter pin is typically bigger than your factory unit (they tend to run .195-.199") and may not fit into the frame hole. The larger diameter pin can create a tighter lockup with the barrel's lower lugs, sometimes such that the gun will not go into battery without gunsmith fitting.
**A popular question is "will this fit in my XXX 1911." As above, every single 1911 will be a little different, and may or may not require gunsmith fitting.
***This part was the OEM slide stop for the Staccato 2011's from 2018-2020, and their current slide stop has a similarly shaped lever. As much as we'd like to sell you a slide stop, you may not gain much from fitting a 10-8 slide stop to a current Staccato. Further, the Staccato factory machines the barrel lugs to the slide stop in your gun, so that they are dimensionally matched for optimum lockup and accuracy. You cannot simply drop in a new slide stop into your Staccato, and doing so may likely result in a fit inferior to the factory's work. For users new to the 1911/2011, the slide stop is to be depressed with the support hand during the reload, and this lever does not extend to the rear to make your gun like a Glock.
Our second generation slide stop is an all original design that is totally reengineered to provide you a whole new level of functionality.
- Unique pad shape that only protrudes approximately .050" more than a GI style, but with a ledge shape that provides a more positive shelf for manipulation
- Interior of lobe angled for easy installation - no more scratches on your slide!
- Engagement surfaces optimized for positive lockback
- Geometry improves slingshot slide release during reloads
- Design improves detent spring pressure to minimize chance of premature lockback
- Optimum diameter .200" (nominal dimension) pin for improved lockup
- Right end of pin has protruding convex domed tip, same as GI slide stops
- Pin is nominal .870" as measured from interior of slide stop plate to the tip of the convex pin
Fits all 1911 pattern pistols, including Govt/Commander/Officer sizes and 2011/Caspian/Para double column frames. Also fits Springfield EMP, which will accept the 9/.38/.40 versions.
.45 ACP version has .200" lobe protrusion.
9mm/.38/.40 version has .220" lobe protrusion. **All calibers other than .45 will use 9/.38 slide stop**
Machined from bar stock and heat treated.
Carbon steel version has black oxide finish.
Stainless Steel version has matte bead blast finish.
Product Reviews (159)
-
Slide lock
Wing that the 10-8 performance is a tenth wider and pin is longer Lock up is stiffer hence taking away any play in the lock up Product works as expected
-
Slide stop
Perfect! Angles are properly cut, great machining, good quality item. Really like the diameter of the pin which is better suited to most frames and helps enhance barrel fit.
-
Slide Stop, Gne 2
I, like many other owners of the Springfield Prodigy, did not find the OEM slide stop big enough. The Gen 2 readily addresses that and had zero adjustments needed to fit the Prodigy.
-
Review
Perfect fit ...
-
Review
Perfect fit ...
-
Slide stop
I have the 10-8 slide stop on my Springfield Prodigy and so far it works fine with no issues.
-
slide stop
Great product and fast shipping. Great upgrade to my prodigy. thanks for the great products and videos
-
Extended slide release
Minor fitting required. Great product, must have for prodigy
-
SA Prodigy Slide Lock
Great quality, fits better than OEM. Drops right in and makes for quicker manipulation. Thanks Hilton!
-
Review
Purchased Gen 2 Slide Stop for Prodigy. Fit was perfect - nice improvement over SA Prodigy OEM part! Have not fired pistol yet with this upgrade. However all function tests (pre-firing) work perfectly. Nice improvement!!!
