Fiber Optic Some Glock slides are thinner at the front sight hole, and the sight's mounting post may protrude.  This causes the set screw to tighten against the sight instead of the slide.  To correct this, file some material off the bottom of the post (indicated in silver) so that the post sits below flush.

Glock Front Sight, Fiber Optic

$45.50 - $49.95

Precision CNC machined from hardened 4140 tool steel and finished in black QPQ salt bath nitrocarburizing (aka Melonite, same as the Glock slide).

  • Fits: ALL Glock models, all calibers, all frame sizes, all slide sizes.
    • Fiber optic (.060" rod with .075" diameter counterbore on 40lpi serrated blade face for flared bulb).
    • Compatible with .250" blade height rear sights.  NOT compatible with Glock factory rear sights, fixed or adjustable, as they are shorter than .250" blade height.
  • Height: .215", .235" and .250"
    • ALL Glock models, regardless of size, caliber, or generation, most commonly use the .215" front.
    • Glock 34/35, 41, 17L, 24L most commonly uses the .235" front. Sights do not overhang slide cutout.
    • Glock 48 uses .250" front with our Glock MOS Standard Height Rear Sight.
    • The .235" front lowers impact approximately 2-3" at 25 yards relative to the .215" front.
    • The .250" front lowers impact approximately 3-5" at 25 yards relative to the .215" front.
    • Please note that different guns will vary in regards to point of impact, especially with differing shooter preference. These heights are recommendations, and we cannot guarantee point of impact due to variations in individual guns. Point of impact will vary by *individual gun* and not so much by generation.
  • Width: .125", .115"
    • Blade width is strictly personal preference.  Thinner fronts cover less of the target area and are preferred for speed.  Thicker blades like the .125" are preferred for improved accuracy and are our most popular.

All sights include set screw and one section each of red and green .060" fiber optic rods.

**INSTALL ONLY TO MAX TORQUE OF 6 INCH/LBS or else you may risk cracking the threaded post.

***Due to manufacturing tolerances by our fiber optic supplier, there may be slight variation in the diameter of the fiber optic rod. Use a razor blade or X-Acto knife at 90 degrees to the rod and gently scrape the outside diameter a little bit and it will fit right in without any compromise to the function.

 

Read our article about sight selection.

 

Please contact us for a discounted price on additional front sights if your initial purchase does not provide the desired point of impact.

Full Description
Glock Front Sight *
Qty
  • Description

    Precision CNC machined from hardened 4140 tool steel and finished in black QPQ salt bath nitrocarburizing (aka Melonite, same as the Glock slide).

    • Fits: ALL Glock models, all calibers, all frame sizes, all slide sizes.
      • Fiber optic (.060" rod with .075" diameter counterbore on 40lpi serrated blade face for flared bulb).
      • Compatible with .250" blade height rear sights.  NOT compatible with Glock factory rear sights, fixed or adjustable, as they are shorter than .250" blade height.
    • Height: .215", .235" and .250"
      • ALL Glock models, regardless of size, caliber, or generation, most commonly use the .215" front.
      • Glock 34/35, 41, 17L, 24L most commonly uses the .235" front. Sights do not overhang slide cutout.
      • Glock 48 uses .250" front with our Glock MOS Standard Height Rear Sight.
      • The .235" front lowers impact approximately 2-3" at 25 yards relative to the .215" front.
      • The .250" front lowers impact approximately 3-5" at 25 yards relative to the .215" front.
      • Please note that different guns will vary in regards to point of impact, especially with differing shooter preference. These heights are recommendations, and we cannot guarantee point of impact due to variations in individual guns. Point of impact will vary by *individual gun* and not so much by generation.
    • Width: .125", .115"
      • Blade width is strictly personal preference.  Thinner fronts cover less of the target area and are preferred for speed.  Thicker blades like the .125" are preferred for improved accuracy and are our most popular.

    All sights include set screw and one section each of red and green .060" fiber optic rods.

    **INSTALL ONLY TO MAX TORQUE OF 6 INCH/LBS or else you may risk cracking the threaded post.

    ***Due to manufacturing tolerances by our fiber optic supplier, there may be slight variation in the diameter of the fiber optic rod. Use a razor blade or X-Acto knife at 90 degrees to the rod and gently scrape the outside diameter a little bit and it will fit right in without any compromise to the function.

     

    Read our article about sight selection.

     

    Please contact us for a discounted price on additional front sights if your initial purchase does not provide the desired point of impact.

  • Reviews

    Reviews

    Jimmy Ward

    10-8 Fiber Optic sights

    The sights are fantastic, especially for those with older eyes. Buy without hesitation, you will not be disappointed.
    Jesse Miranda

    Great sights

    Got these FO sights to replace my Heinie night sights. These pop so good. Love them. I can acquire targets a lot faster. Highly recommend
    Joseph Potter

    Glock front sight

    Perfect fit, great quality
    Daniel Price

    Glock front fiber optic sight

    I like the sight but the red fiber optic rod was a bear to feed into the sight, really, really tight. The green wouldn't even begin to feed. But once I got it in I like the sight picture it gives me on my Glock 44.
    Joey Villanueva

    Sights

    Simply the best sights...
    Solomon

    Glock front sight

    Nicely machined front fiber optic sight. The serrations on the front of the sight are crisp and allow my eyes to focus clearly on the front sight. The fiber optic rod fits securely and is relatively easy to install. My only suggestion would be to include a couple of extra rods with the sight or have additional rods available for purchase.
    Ignacio

    Sights

    Love the product and specially customer service Thanks
    Pilgrim

    Glock Rear Sight Low Profile

    Excellent design for a ‘modern’ rear sight. Easy installation and a perfect fit in my G48 slide.
    Stuart Ashton

    Sights and service!

    I was very pleased with both my sights and the service I received on my last order from 10-8 Performance. The sights are first class and the service was outstanding. Thank you.
    Zachary

    Glock Fiber Optic Front Sight

    By far the best fiber optic front sight on the market. There is no play or wobble between the slide and the sight. The sight screw is made of great quality and will not mare when tightened. I have used several other companies fiber optic front sights. The 10-8 Performance absolutely destroys the competition in quality.
  • Videos

    Videos